LEXMARK OPTRA S 1855 DRIVER FOR MAC DOWNLOAD

Documentary

Check LVPS cable for continuity. The main motor is located just to the left of the toner cartridge. If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. A secondary error indication can be obtained by pressing an releasing a button. Great that you have that part in stock and thank you for your quick reply. Check the continuity of the fuser lamp at the two heavy leads. A error caused by low line voltage can sometimes be cleared by turning the machine off and then on again.

Uploader: Zulkizuru
Date Added: 27 May 2010
File Size: 53.28 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 97408
Price: Free* [*Free Regsitration Required]

No inkjet error codes available Error Code. May be due to the paper feeding manually while motors running and previous page in path.

Open the printer rear door to access the jam. The transfer roller is included in the maintenance kit.

Lexmark Printer Drivers

Thank you and your firm again, you lesmark terrific. Great that you have that part in stock and thank you for your quick reply. Error 84 Transfer Drum Exhausted. We got it this morning and I have it installed. Thank you for the speedy shipment and response. Check fan for binding or defective bearing – Replace Fan How did we do?

No inkjet error codes available. Remove lsxmark duplex front cover to access the jam area. Indicates that the lexmark optra s 1855 is below standby temperature when the printer is idle. Check the wiring harness cable. The pin should enter the tower on the HVPS and depress the cover switch. Fuser errors can be from a cold lexmark optra s 1855 or an overheated fuser.

Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly.

Support | Lexmark

The main motor is located just to the left of the toner cartridge. If the paper is jammed lexmark optra s 1855 the rear of the duplex, replace the duplex front cover and open the duplex rear door. Error Color Machines. This error indicates the printer was able to read the cartridge ID, but the ID did oexmark pass the verification test.

Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the lexmark optra s 1855 position if applicable to your machine.

The fuser, melts or fuses the toner to the media and has a heat roller and lexmark optra s 1855 pressure roller. The fuser can usually be removed with two simple screws and the entire assembly lifted out. Run the Lexmrak Disk Test. Replace bump motor Replace interlock switch Replace System Card. May require service technician Press “GO” to clear message and temporarily continue.

Replace the transfer roller as necessary. I truly appreciate it.

Lexmark Printer Drivers by Model

Observe lexmark optra s 1855 lamp through the left near side of the printer. Save time and money ,exmark servicing your own Lexmark printer Lexmark Laser Printer Error Codes Lexmark error codes may not apply equally to all models. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn lexmark optra s 1855 on and try again.

Jam at the duplex unit. Lexmark Fusers How did we do? Wayne Haub Kansas City. Page too complex to print. Printhead Error – May have sub-codes.

Replace with the correct printhead. If cables, connectors and connections are good replace assemblies listed. Serial Error – Framing or parity error on serial. Fuser is below standby temperature when idle.

Erase lamp assembly missing or disconnected. If either the error or the error returns after you lexmark optra s 1855 on the printer or when you try to print, the printer will require service.

POR several times Check each board for secure ground. Input Paper Sensor was not triggered – Paper may be jammed at the sensor. A secondary error indication can be obtained by pressing an releasing a button. Flash Full – Not enough flash memory for data requested to be stored.

Make sure top access door is closed securely 2. Most cost effective lexmark optra s 1855 is to replace the fuser Lexmark Fuser Pricing. The Transfer drum has reached the end of it’s life and must be replaced. Replace the Autocompensator Assy. Software Error Unrecoverable software error. Requires further measurement The printhead laser scanner does not contain any serviceable parts. The main motor assembly may need lexmark optra s 1855 be replaced.

Veronica Casto Houston, TX.